Get the free FUME HOOD Clean-up and Inspection Form - oregonstate

This form is used for the clean-up and inspection process of fume hoods in a lab environment, ensuring that all safety and contamination protocols are followed before removal or disposal.

How to fill out fume hood clean-up and

How to fill out FUME HOOD Clean-up and Inspection Form

1. Acquire the FUME HOOD Clean-up and Inspection Form from your lab supervisor or facility manager.
2. Begin filling out the date and the name of the person conducting the inspection at the top of the form.
3. Inspect the fume hood for any visible signs of contamination or damage.
4. Check the airflow indicator to ensure it is functioning correctly and within acceptable limits.
5. Clean the fume hood surfaces and document the cleaning procedure on the form.
6. Record any issues or maintenance needs observed during the inspection.
7. Sign and date the form upon completion, indicating that the inspection was carried out.

Who needs FUME HOOD Clean-up and Inspection Form?

1. Laboratory personnel who regularly use fume hoods for experiments.
2. Safety officers responsible for ensuring compliance with safety regulations.
3. Facility managers overseeing the maintenance and safety of laboratory equipment.
4. Anyone conducting research that involves volatile or hazardous materials requiring fume hood usage.

People Also Ask about

How often should I clean my fume hood?

Frequency of use: If you use a fume hood on a regular basis, develop a cleaning schedule. If your hood isn't used often, clean it immediately afterward. Ducted fume hoods used with low-risk chemicals can go months without a clean. Fume hoods used for dangerous or varied processes need cleaning after every use.

What is the cleaning procedure for fume hood?

Clean the interior and exterior surfaces and sash periodically, and after spills, using deionized water; then wipe the areas down with a soap solution and rinse. NOTE: Personnel should wear appropriate PPE when cleaning the fume hood to protect themselves from the chemicals.

How do you inspect a fume hood?

Process: Turn on hood. Check the vaneometer. Match the arrow on the hood sash with the arrow on the side panel of the hood. To acquire reading, hold vaneometer in the center of the hood. Acceptable standard -Chemical fume hoods should operate at a face velocity of (80-120) Linear Feet Per Minute.

How often should a hood system be inspected?

How often should a kitchen hood fire suppression system be inspected? The system should be inspected every six months, looking for problems like defective heat and flame detectors, leaking suppressant tanks, clogged nozzles, or defective cartridges.

What is the OSHA standard for fume hoods?

OSHA: “General air flow should not be turbulent and should be relatively uniform throughout the laboratory, with no high velocity or static areas; air flow into and within the hood should not be excessively turbulent; hood face velocity should be adequate. (Typically 60-110 fpm.)”

How often should fume hoods be certified by EHS?

All fume hoods must be re-certified annually by EHS.

How often do fume hoods need to be inspected?

ing to the standards set forward by OSHA, chemical fume hood testing should be conducted on an annual basis at a minimum. Additionally, new fume hoods should be tested upon installation prior to utilization. It also is recommended that a reevaluation should be performed any time changes are made to the equipment.

What is the standard for fume hood testing?

ASHRAE standard 110 is widely accepted around the world. It has set testing guidelines for the methods and procedures to rate fume hood performance. Fume hood testing consists of three key areas: face velocity measurement, smoke visualization, and tracer gas containment.

For pdfFiller’s FAQs

What is FUME HOOD Clean-up and Inspection Form?

The FUME HOOD Clean-up and Inspection Form is a document used to record the maintenance, cleanliness, and functionality of fume hoods to ensure proper safety standards and compliance with regulations.

Who is required to file FUME HOOD Clean-up and Inspection Form?

Laboratory personnel, safety officers, and facility managers who are responsible for the maintenance and operation of laboratory fume hoods are required to file the FUME HOOD Clean-up and Inspection Form.

How to fill out FUME HOOD Clean-up and Inspection Form?

To fill out the FUME HOOD Clean-up and Inspection Form, it is necessary to provide details such as the date of inspection, the condition of the fume hood, any issues found, actions taken for cleaning or repairs, and the signatures of the person conducting the inspection.

What is the purpose of FUME HOOD Clean-up and Inspection Form?

The purpose of the FUME HOOD Clean-up and Inspection Form is to ensure that fume hoods are functioning properly, maintained in a clean state, and meet safety standards to protect laboratory personnel from hazardous fumes.

What information must be reported on FUME HOOD Clean-up and Inspection Form?

The information that must be reported on the FUME HOOD Clean-up and Inspection Form includes the date of inspection, fume hood identification number, name of the inspector, inspection findings, cleaning activities conducted, and any repairs needed or performed.