Get the free RADIATION SURVEY REPORT: Form AU-2 - uml

This document is used to report and document radiation surveys conducted in a facility, including details on authorized users, types of radiation sources, equipment used, and measurement results.

How to fill out radiation survey report form

How to fill out RADIATION SURVEY REPORT: Form AU-2

1. Obtain the RADIATION SURVEY REPORT: Form AU-2 template.
2. Fill in the date of the survey in the designated section.
3. Provide the location where the survey was conducted, including specifics such as room number or site.
4. Identify the personnel conducting the survey; include names and titles.
5. Record the measurement results in appropriate units (e.g., mR/hr, counts per minute).
6. Indicate the method used for taking measurements and the type of radiation measured.
7. Include any relevant background radiation levels noted during the survey.
8. Document any unusual findings or concerns observed during the survey.
9. Sign and date the report at the end, ensuring all necessary fields are filled.

Who needs RADIATION SURVEY REPORT: Form AU-2?

1. Personnel involved in radiation safety management.
2. Regulatory agencies that oversee radiation safety compliance.
3. Health and safety officers in organizations that use radioactive materials.
4. Individuals conducting routine or incident-based radiation surveys.

People Also Ask about

What is a radiation report?

These services include radiation dose measurements for persons who enter areas where they may be exposed to radiation or radioactive material. The results are periodically reported to monitored individuals.

What is the periodicity of radiation protection survey?

Radiation Monitoring (b) The radiation survey meter should be periodically calibrated, at least once in two years and records are maintained. (c) The calibration of a radiation survey meter should be traceable to the national/international standards laboratory.

When must a radiation survey be performed?

After each day of radioactive material usage/experimentation. After transfer of radioactive material from stock solutions. After each experimental run if there is a possibility of a change in radiation levels or contamination. After a minor radioactive spill clean up or emergency.

How often should a radiation storage area be surveyed?

Monthly surveys must be performed every calendar month in which radioactive material is possessed.

What is a Category 2 radiation source?

These sources are typically used in radiothermal generators, irradiators, and radiation teletherapy. Category 2 sources, if not safely or securely managed, could cause permanent injury to a person who handled them or was otherwise in contact with them for a short time (minutes to hours).

How often must a radiation leak test be performed?

(1) Each sealed source (except an energy compensation source (ECS)) must be tested at intervals not to exceed 6 months. In the absence of a certificate from a transferor that a test has been made within the 6 months before the transfer, the sealed source may not be used until tested.

How do you do a radiation survey?

With the appropriate probe, a meter survey is conducted by slowly passing the probe over the area or object to be surveyed. Be certain to survey at a constant speed - approximately 2 cm/sec. The distance from the surface or object should also be constant. A distance of 1 cm is suggested.

When should radiation surveys be done?

The Authorized User of the radiation laboratory is required to have a radiation survey conducted under the following conditions: After each day of radioactive material usage/experimentation. After transfer of radioactive material from stock solutions.

For pdfFiller’s FAQs

What is RADIATION SURVEY REPORT: Form AU-2?

RADIATION SURVEY REPORT: Form AU-2 is a document used to report the results of radiation surveys conducted to assess exposure levels and ensure compliance with safety regulations.

Who is required to file RADIATION SURVEY REPORT: Form AU-2?

Individuals or organizations that utilize radioactive materials or radiation-producing equipment and are subject to regulation by health or safety agencies are required to file RADIATION SURVEY REPORT: Form AU-2.

How to fill out RADIATION SURVEY REPORT: Form AU-2?

To fill out RADIATION SURVEY REPORT: Form AU-2, gather the necessary data from radiation monitoring equipment, complete sections pertaining to the date, location, type of measurements, and results, ensuring accuracy for compliance and review.

What is the purpose of RADIATION SURVEY REPORT: Form AU-2?

The purpose of RADIATION SURVEY REPORT: Form AU-2 is to document radiation levels in a given area, ensuring safety and compliance with regulatory standards to protect workers and the public from harmful exposure.

What information must be reported on RADIATION SURVEY REPORT: Form AU-2?

The information that must be reported includes the location of the survey, time and date of measurements, type of radiation detected, survey results, and any necessary recommendations or observations.